CCNA quick study dumps 1

1:All but one of the following is an OSI
layer, which is NOT?
A. Application
B. System
C. Network
D. Physical
Ans:B

2:Which of the following are connectionoriented
protocols? (Choose all that apply)
A. TCP
B. IP
C. FTP
D. ICMP
E. SNA
Ans:A C

3:Bits are converted to frames at which
layer of the OSI model? (Choose all that
apply)
A. Physical
B. Data link
C. Layer 2
D. Layer 3
Ans:B C

4:Routing of IP is a function of which
OSI layer?
A. Physical
B. Data link
C. Mac-sublayer
D. Network
Ans:D

5:Frame relay is what type of protocol?
A. Routing
B. Routed
C. Connection oriented
D. Connection-less
Ans:C

6:To set an interface to PPP mode what IOS
command is required? Assume you are in
interface mode.
A. ppp encapsulation
B. encapsulation ppp
C. set ppp
D. set encap ppp
Ans:B

7:How do you log into a router in Privilege
mode?
A. Use console port only
B. Use the Aux port
C. Type the enable password
D. You must be a Cisco TAC engineer
Ans:C

8:What IOS command will copy the running
config to NVRAM?
A. Copy running-config NVRAM
B. copy runn start
C. copy config runn
D. copy mem running-config
Ans:B

9:A MAC-address is made up of what two
entities?
A. IP address
B. Vendor code
C. Serial Number
D. Sales address
Ans:B C

10:What is the correct sequence of keys to
break out of a trace route in a Cisco router?
A. Ctrl+shift+6
B. Ctrl+shift+6 then x
C. Ctrl+shift+break
D. Ctrl+shift+x then break
Ans:B

11:Which OSI layer does IPX operate at?
A. data link layer
B. network layer
C. transport layer
D. session layer
Ans:B

12:An Internal IPX network number is required
by what servers and protocols?
a) IPX RIP router
b) NLSP capable device
c) IPX server
d) NSLP server
e) All of the above
Ans:B C D

13:The two key parts of a network level
address are (choose two)?
a) A datalink address
b) A network address
c) A DNS address
d) A node address
e) A netbios name
Ans:B D

14:What is the command to load an IOS
image from a TFTP server?
a) write tftp
b) copy IOS Flash
c) xmodem –c
d) copy tftp flash
e) copy tftp running-config
Ans:D

15:Which of the following are benefits of
segmenting networks with routers, as opposed to
using repeaters only?
a) Lower cost
b) Fewer collisions
c) Fewer Broadcasts
d) Full Duplex capability
e) More available IP addresses
f) A collapsed network backbone
Ans:B C

CCNA quick study dumps

1:To monitor ipx traffic on a network, what command would you use?
• A. debug ipx transaction
• B. show ipx traffic
• C. show ipx events
• D. display ipx traffic
Ans B


2:What command would you use to find out the names of Novell servers on a network?
• A. show ipx servers
• B. show ipx hosts
• C. show ipx sap
• D. show ipx nodes.
Ans A

3:The "ipx delay number" command will allow an administrator to change the default settings. What are the default settings?
• A. For LAN interfaces, one tick; for WAN interfaces, six ticks
• B. For LAN interfaces, six ticks; for WAN interfaces, one tick
• C. For LAN interfaces, zero ticks; for WAN interfaces, five ticks
• D. For LAN interfaces, five ticks; for WAN interfaces, zero Ticks
Ans A

4:What does the "IPX maximum-paths 2" command accomplish?
• A. It enables load sharing on 2 paths if the paths are equal metric paths.
• B. It sets up routing to go to network 2.
• C. It is the default for Cisco IPX load sharing.
• D. It enables load sharing on 2 paths if the paths are unequal metric paths.
Ans A

5:You want to enable both arpa and snap encapsulation on one router interface. How do you do this?
• A. The interface can handle multiple encapsulation types with no extra configuration.
• B. Assign two network numbers, one for each encapsulation type.
• C. Enable Novell-ether to run multiple encapsulation types.
• D. Both arpa and snap are enabled by default so you don't have to configure anything.
Ans B

6:10 Novell's implementation of RIP updates routing tables every ____ seconds.
• A. 60
• B. 90
• C. 10
• D. 30
Ans A

7:What is the Cisco name for the encapsulation type used on a serial interface?
A. HDLC
B. SDLC
C. SAP
D. SNAP
Ans A

8:"arpa" is used by the Cisco IOS for which encapsulation types?
A. Ethernet_II
B. Ethernet_802.3
C. Ethernet_802.2
D. Ethernet_SNAP
Ans A

9:15"sap" is used by the Cisco IOS for which encapsulation types?
A. Ethernet_802.2
B. Token-Ring
C. FDDI_SNAP
D. Ethernet_802.3
E. FDDI_802.2
Ans A,B &E

10:Which type of Ethernet framing is used for TCP/IP and AppleTalk?
A. Ethernet 802.3
B. Ethernet 802.2
C. Ethernet II
D. Ethernet SNAP
Ans D

11:Which type of Ethernet framing is used for TCP/IP and DECnet?
A. Ethernet 802.3
B. Ethernet 802.2
C. Ethernet II
D. Ethernet SNAP
Ans: C

12:You are a system administrator on a NetWare network, you are running NetWare 4.11 and you cannot communicate with your router. What is the likely problem?
A. NetWare 4.11 defaults to 802.2 encapsulation.
B. NetWare 4.11 defaults to 802.3 encapsulation
C. Cisco routers only work with NetWare 3.11.
D. NetWare 3.11 defaults to 802.2 encapsulation.
Ans A

13:Which NetWare protocol works on layer 3--network layer—of the OSI model?
A. IPX
B. NCP
C. SPX
D. NetBIOS
Ans A

14:Which NetWare protocol provides link-state routing?
• A. NLSP
• B. RIP
• C. SAP
• D. NCP
Ans: A

15:In the command "router igrp 109" what does 109 signify?
• A. an autonomous system
• B. any network number which the router is attached to
• C. the allowable length of the routing table
• D. the network socket number
Ans A

16:The command "show IP protocol" displays which information?
• A. routing timers
• B. network information
• C. contents of the IP routing table
• D. information about all known network and subnetworks
Ans A & B

17:You are logged into a router, what command would show you the IP addresses of routers connected to you?
• A. show cdp neighbors detail
• B. show run
• C. show neighbors
• D. show cdp
Ans A

18:As a system administrator, you need to provide your routers with a Domain Name System (DNS) server. How many DNS servers can you specify with one command?
• A. 6
• B. 1
• C. 2
• D. 4
Ans A

19:How would you configure one host name that points to two IP addresses?
• A. IP host jacob 1.0.0.5 2.0.0.8
• B. IP jacob 1.0.0.5 2.0.0.8
• C. IP host jacob 1.0.0.5
• D. IP host duplicate "all"
Ans A

20:There are two processes to pair MAC address with IP addresses. Which process finds an IP address from a MAC address?
A. RARP B. ARP C. RIP D. IGRP
Ans A

21:When the router runs out of buffer space, this is called ________.
A. Source Quench B. Redirect C. Information Request D. Low Memory
Ans A

22:Which layer hides details of network dependent information from the higher layers by providing transparent data transfer?
A.) Transport B.) Physical C.) Data Link D.) Session E.) Application F.) Network
Ans A

23:What information is provided by the local management interface (LMI)? A.) LMI encapsulation type B.) The current DLCI values C.) The status of virtual circuits D.) The global or local significance of the DLCI values
Ans B C D

24:What is the IEEE specification for Spanning Tree Protocol?
A.) 802.9 B.) 803.ud C.) 803 D.) 802.1d
Ans D

25:Which of the following are Session Layer standards? A.) ASCII and EBCDIC B.) MPEG and MIDI C.) NFS and SQL D.) JPEG and PICT
Ans C

INTRODUCTION

This is a blog for CCNA guys who are trying to take CCNA exam and also for those who need a short study guide to remember the important points in this course.It can be used as CCNA dumps as the questions may be vary in style only,so you can use this resource as an exam preparation guide.


Points to remember to take CCNA Exams

1:some questions may be lengthy ,so don't waste your time to reading it excessively,just check the important points asked in the questions and try to answer.

2:We should complete a quick study guide of ccna before writing the exams and there is a lot of commands to study in ccna,there is a more chance to forgot those commands.Try to take an sample exam with exam simulators.

3:It is a must to practice the CCNA practicals in Lab of using Simulators.There are a lot of simulators available and the best one is Boson Netsim simulator.There are also simulators like semsim but should be used by a CCNA starter guide only.